Tools

6" Flat Nose Hemostat tool by Shawn O'Hare for Dermal Anchor Insertion.

410 ASTM Stainless Steel. The best tools on the market right now. With the flat nose of this hemostat, you can clamp any size dermal anchor head. Because the head of this hemostat is flat, inserting the dermal anchor remains flush against the body.

5" pliers for small to medium rings. 410 ASTM surgical stainless steel and fully autoclavable. You can sterilize these repeatedly without rusting. These pliers have deep grooves on the head end for captive rings 1/2" and smaller.

Perfect tool for rings 20g - 8g

6" long high quality 410 Surgical steel Septum Forcep.

Head "receiving tubes" are big enough to allow up to a 12g Needle to pass through with ease.

These forceps are for septums, but they also work very well for lining up nipple piercings, ear piercings, and even eyebrow piercings.

Thin MicroDermal Surface Anchor Holder Tool - Great for Changing Tops

This tool was designed by Jason Coale.

• 2.45" Long
• 14g Thick at the Rod
• .8mm Thick Head
• 2.8mm Wide Head

This tool is similar in design to a shoe horn. You would use this to drop the heel of the anchor into the hole much like a shoe horn. This tool also works well for removal.

Threaded Taper for Internally threaded Jewelry, Dermal Anchors, etc..

Taper is 14g at its thickest point and has a 1.2mm thread on the end.

Use these to insert internally threaded jewelry or your dermal anchors. The size of the taper is the thickest part. Measures 4 inches long.

Tool measures 60mm long and is 4mm thick and has a 1.2mm thread pattern on the end.

Use these to insert internally threaded jewelry or your dermal anchors.

5 inch ring opening pliers with 2 notches for opening and a needle nose tip for tight spaces.

Opens captive rings to help in removing and inserting beads.

Works best on rings from 1/4" to 5/8" in diameter, and up to 8 gauge in thickness.

5" length. Made from high grade 410 ASTM surgical steel.

Excellent for inserting dermals.

Visually appealing black oxide coated steel pennington forceps. Not only do they look good, they also help prevent eye fatigue by reducing light glare when in use. But best of all, the black oxide also acts as a protection against corrosion, giving your tools a longer life.
These small sized pennington forceps are excellent for clamping hard-to-reach or tighter areas during a piercing procedure.
This tool measures at a total of 6” long with the inner tip measuring 11mm long and 5mm wide at the top.
The slotted opening is 2mm, which will clear needles up to 14g.

Specs

• Material: 410 ASTM Stainless Steel with Black Oxide Coating
• Forceps Length: 6”
• Inner Tip Length: 11mm
• Inner Tip Width (at top): 5mm
• Slot Opening: 2mm
• Serrated jaws for secure grip
• Interlocking teeth near finger loops

Mini Ring Opening Pliers - Perfect for Tight Places.

Opens ring to help in removing and inserting beads from captive rings.

Works best on rings from 1/4" to 3/8" in diameter and up to 14 gauge in thickness. 

Great ring opening pliers for when doing tragus, eyebrow, ear, or any small, tight piercings.

Multi-purpose opener and closer. Autoclave and reuse. Not intended for heavy gauge rings. Not a replacement for traditional openers and closers.

Taper is 10g at its thickest point and has a 1.2mm x 2.0mm thread on the end. Use these to insert internally threaded jewelry. The gauge of the taper is the thickest part. Measures 1 inch in length(25mm long)  Autoclave safe.

Visually appealing black oxide coated steel pennington forceps. Not only do they look good, they also help prevent eye fatigue by reducing light glare when in use. But best of all, the black oxide also acts as a protection against corrosion, giving your tools a longer life.
These small sized pennington forceps are excellent for clamping hard-to-reach or tighter areas during a piercing procedure.
This tool measures at a total of 6.5” long with the inner tip measuring 8mm long and 4.7mm at its widest point.
The slotted opening is 2.2mm, which will clear needles up to 14g.

Specs

• Material: 410 ASTM Stainless Steel with Black Oxide Coating
• Forceps Length: 6.5”
• Inner Tip Length: 8mm
• Inner Tip Width: 4.7mm
• Slot Opening: 2.2mm
• Serrated jaws for secure grip
• Interlocking teeth near finger loops

Ring Opening Pliers with 3 Notches and a needle nose for tight spaces.

Opens captive rings to help in removing and inserting beads.

Works best on rings from 1/4" to 3/4" in diameter, and up to 6 gauge in thickness.

Tweezer style triangle end forceps with locking mechanism.

Great alternative to regular forceps due to being lighter and smaller than regular forceps. Easy to use with one hand. 

These tweezer forceps are approximately 5-3/4". They have a 12mm head with a 7mm inner hole diameter.

These forceps are only available without slots.

Taper is 12g at its thickest point and has a 1.2mm x 2.0mm thread on the end. You are purchasing 1 taper

4 1/2" Ring Opening Pliers - Perfect for tiny captives.

Opens rings to help when removing and inserting beads.

Works best on rings in tight places and small diameter rings.

These work backwards to the conventional ring opener pliers. You squeeze to close.

These Calor Style tapers are made with Medical Grade 304 Stainless Steel.  They can be autoclaved and reused.  
Each taper is approximately 2" in length and tapers down 2 gauges smaller than the listed size for easy insertions.
For example, the 0g (8mm) taper at its thinnest point is approximately 4g (5mm).

Calor Style Tapers are thicker and recessed at the large end so you can fit the jewelry inside the taper; this makes for a seamless flow from taper to insertion of jewelry and helps to prevent slipping.

Taper Dimension Chart:

Bend the perfect nostril screw every time! Over the years we have heard many piercers ask for either shorter or longer nostril screws, or screws with more acute or obtuse bends on the end.

This tool eliminates those problems. Use this tool with out U-Bend nostril pins.

You pick the wearable area, and the degree of the screw bend. Scroll down for detailed instructions on how to use this item.

Crafted from 410 ASTM Stainless Steel.

5-1/2" pliers for medium to large rings. 410 ASTM surgical stainless steel and fully autoclavable. You can sterilize these repeatedly without rusting. These pliers have deep grooves on the head end for captive rings 5/8" and larger.

Perfect tool for rings 20g - 6g

PTFE threading tool that works on both 16g & 14g PTFE.

You will receive 1 threading tool. On one side you can thread 16g - 1.2mm and on the other side you can thread 14g - 1.6mm

A two-in-one tool with a nice textured grip for easy threading.

Made from 410 ASTM Steel and is 3" (75mm) long and 8mm (5/16") thick.